1. Home
  2. Mixer
Prev
QSC RMX Series RMX 2450
QSC RMX Series RMX 2450KShs40,000.00
Next
Pro-Sound WM 5537KShs14,000.00
QSC RMX Series QSC 1450
View details

QSC RMX Series QSC 1450

(0 customer reviews) 0 sold

KShs75,000.00

QSC RMX Series QSC 1450

The RMX1450 power amplifier steps up the output to 280 watts/channel at 8 ohms; 1400 watts at 4 ohms bridged — with the low distortion you expect from QSC.

QSC RMX Series QSC 1450 Overview

QSC’s RMX Series amplifiers give you clean, dynamic power with the legendary QSC sound quality and reliability that pros depend on. The RMX Series delivers unmatched performance at a breakthrough price.

QSC RMX Series QSC 1450 Muscular Power Plant

The power supply is the heart of an amplifier, converting raw AC power from the wall to clean DC for the audio circuitry. The RMX uses a powerful high-current toroidal transformer and ample filter capacitance to ensure generous energy reserves.

This makes a critical difference in sound quality, allowing the amp to effortlessly punch out high level transients, even when driving abusive 2-ohm speaker loads.

QSC RMX Series QSC 1450 Superior Performance

RMX amplifiers deliver true studio-quality sound. A full complementary output circuit using the highest-grade linear output devices delivers ultra-low distortion (<0.05% THD) and a ruler-flat frequency response.

SMT (Surface Mount Technology) triples small-signal component density, enabling them to pack up to 2400 watts of power in a chassis only 2 rack spaces and less than 16″ deep. And unlike other designs, RMX output devices are direct-mounted to the heat sink for optimum thermal coupling and cooling.

QSC RMX Series QSC 1450

KShs75,000.00

Add to cart
Buy Now
Category:

QSC RMX Series QSC 1450 Specifications

Output Wattage, Stereo Mode (EIA: both channels driven):
8 ohms EIA 1 kHz 0.1% THD: 280W
4 ohms EIA 1 kHz 0.1% THD: 450W
2 ohms EIA 1 kHz 1% THD: 700W

Output Wattage, Bridge Mono Mode:
8 ohms EIA 1 kHz 0.1% THD: 900W
4 ohms EIA 1 kHz 1% THD: 1400W

Signal to Noise (20 Hz-20 kHz): 100dB
Distortion (SMPTE-IM): Less than 0.01%

Input Sensitivity @ 8 ohms: 1.12v (+3.4 dBu)
Voltage Gain: 40x (32 dB)
Output Circuitry: AB
Current Consumption (1/8 power pink noise at 4 ohms @ 120VAC,both channels driven; multiply current by .5 for 230V units.): 7A
Distortion (typical): 20 Hz-20 kHz: 10 dB below rated power: Less than 0.03% THD 4 and 8 ohms
1.0 kHz and below: full rated power: Less than 0.03% THD 4 and 8 ohms
Frequency Response: 20 Hz-20 kHz, 0/-1 dB, -3 dB points: 5 Hz-50 kHz
Damping Factor (1 kHz and below): greater than 300 at 8 ohms
Input Impedance: 10 K ohms unbalanced, 20 K ohms balanced
Input Clipping: 10 Vrms (+22dBu)
Cooling: Continuously variable speed fan, rear-to-front air flow
Connectors (each channel): Input: Active balanced; barrier strip, XLR,and 1/4″ (6.3 mm). TRS tip and XLR pin 2 positive
Output: “Touch-proof” binding posts and Neutrik Speakon
Controls: Front: AC switch, Ch.1 and Ch.2 gain knobs
Rear: 10-position DIP switch
Indicators: PWR-ON: Green LED SIGNAL: Yellow LED (1 per channel) CLIP: Red LED (1 per channel)
Amplifier Protection: Full short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loads.
Load Protection: Turn-on/off muting, AC coupling (850, 1450), triac crowbar (2450, on each channel)
Power Requirements: 100, 120 VAC, 50-60 Hz
Operating Voltage: 110V
Dimensions: rack mounting: 48.3cm (19″); 8.9cm (3.5″) tall (2 rack spaces); 40cm (15.9″) deep (rack mounting to rear support ears)
Net Weight: 18.2 kg (40 lbs.)

QSC RMX Main Feautres

  • Power Per Channel @ 8 Ohm: 280W RMS
  • Power Per Channel @ 4 Ohm: 450W RMS
  • Power Per Channel @ 2 Ohm: 700W RMS
  • Signal-to-Noise: -100dB
  • Distortion: <0.01%
  • Input Sensitivity @ 8 Ohm: 1.15V (+3.4dBu)
  • Voltage Gain: 40x (32dB)
  • Frequency Response: 20Hz-20kHz
  • Damping Factor (1kHz & Below): >300 @ 8 Ohm
  • Input Impedance: 10kOhm Unbalanced; 20kOhm Balanced
  • Input Stage Clipping: 10V RMS (+22dBu)
  • Cooling: Continuously Variable Speed Fan
  • Input: Active Balanced 3-Pin Euro-Style Detachable Terminal Block & XLR
  • Output: Touch-Proof Binding Posts, Neutrik Speakon
  • Controls: AC Switch, Channel Gain Knobs, 10-Position DIP Switch
  • Weight: 18.2kg

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Shipping Details

  • Please pay more attention to your order address which MUST MATCH your shipping address. (If you’re from Russia, Please leave your full name. It is very important)
  • Items will be shipped within 3 business days after payment.
  • Please check items when delivered, if damaged, please kindly accept it and contact us immediately.  We will make a confirmation and resend you a new one.

 

Shipping By Shipping Cost Estimated Delivery Time Tracking Information
Thembay Express Free Shipping 12-20 days Not available
LEX $20.00 - $50.00 04-12 days Available
Lorem Ex $26.00 - $70.00 03-17 days Available

Packaging Details

  • Unit Type: piece
  • Package Size: 25cm x 32cm x 5cm (9.84in x 12.60in x 1.97in)
  • Package Weight: 0.56kg (1.23lb.)

Warning: Attempt to read property "post_title" on null in /home/drumjbco/public_html/wp-content/plugins/js_composer/include/helpers/helpers.php on line 63
Call Us now